Top 10 typical forklift crashes ， forklift procedure need to take notice of these issues ！.

Don't underestimate the forklift at the workplace. If the operation is not good, there will be major mishaps in mins, and there are several crashes entailing forklifts.

Case 1: The forklift freight obstructed the driver's sight, and the person in front can not be located, causing a moving crash.
Instance 2: In order to preserve the equilibrium of the forklift when lifting heavy goods, the employees used their body weight as the weight, which virtually created casualties.
Instance 3: The size of the forklift freight goes beyond the permitted width of the route and hangs on the roadside rack, which nearly triggers an mishap.
Case 4: Forklift is speeding up and surrender throughout a turn.
Case 5: The forklift driver did not notice the pedestrian, and the pedestrian did not see the forklift.
Instance 6: The forklift lifts the personnel unlawfully, the forklift motorist does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety and security of driving, beep the horn first and afterwards start.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure (air pressure) scale must be secure before beginning.
3. When the forklift starts with a tons, the driver must first verify that the load is steady and dependable.
4. The beginning must be sluggish and steady.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the pole ought to be slanted backward. .
2. Do not lift the fork expensive when driving. When entering and leaving the task website or while driving, be careful that there will be no barriers in the sky. When the tons is taking a trip, the fork must not be increased expensive, which will impact the security of the forklift. .
3. After dumping, the fork ought to be reduced to the regular driving position before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued initially. High-speed doglegs are restricted. High-speed sharp turns will certainly create the vehicle to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to switch off the fire and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are special scenarios.
6. When the forklift is running, it has to comply with the traffic rules in the factory and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the tons should be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The load shall not be raised except when piling or filling. .
8. The elevation of the lots need to not block the chauffeur's sight. In special circumstances, when the item influences the forward vision, drive at a reduced rate when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it needs to drive safely at a low rate when getting in the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to depend on the fork to hold things and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported in a prompt manner, and they will certainly never ever operate with illnesses or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks need to be changed as needed to make the lots of the two forks well balanced and not skewed, and one side of the product should protest the rack. .
2. It is restricted to deal with a solitary fork or utilize a fork top or pull. In unique situations, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging things, the forklift needs to be stopped with the brake. .
4. The rate of the vehicle must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it should be noted that the fork pointer ought to not touch various other items or objects. The lots should be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted onward slightly when the tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so regarding stay clear of the collapse of the goods and injure people. .
8. Overloading is forbidden, and it is banned to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to select, transform pallet unload.

Leaving .
1. It is restricted to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake deal with to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for unique circumstances, such as the driver does not leave the vehicle's line of sight and does Electric Forklift Truck for Warehouse not go beyond 1 min).
4. Get rid of the secret. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be checked, and gas, lubing oil and cooling water ought to be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, check whether the pressure and temperature are regular.
5. After the forklift is running, the outside leakage should additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the vehicle must be driven backwards when declining;.
8. When the forklift personnel Electric Forklift Truck for Warehouse bring the goods and move forward, if they come across large or heavy items and go to the vehicle driver's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Solitary fork operation is not permitted.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia pressure to pick up the goods.
6. It is not enabled to make use of stopping force to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is raised.
8. Do not drive laterally on inclines
.
Parking is not permitted under the following problems.
1. Contours, slim roadways, train crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same size as the obstacle should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844